19x20 Water to Air Heat Exchanger~~1" Copper ports w/ EZ Install Front Flange

<h2><strong>19x20/152,000BTUs/ 180 PSI</strong><span>For use in yourhot air furnace plenum.</span></h2><p style="text-align: left;"><span><b>***Notrecommendedfor air compressors***</b></span></p><p style="text-align: left;"><b><strong><u>Information about our heat exchangers</u></strong></b></p><ul><li><b><strong>This heat exchanger is ideal for a 19"x 21" plenum or larger.</strong></b></li><li><b><strong>The outlets come out on the 19" side (shown as the vertical side in the picture above)</strong></b></li><li><b><strong>GPM 15.8 </strong></b></li><li><b><strong>CFM 1854 </strong></b></li><li><b><strong>The fin area is 19"x 20"</strong></b></li><li><p><strong>Outside Dimensions 20”(width)x22.5”(Length from Manifold to Base)x3.5”(Thickness)</strong></p></li><li><b><strong>There is a 1" frame on the end opposite the outlets that covers the copper elbows. This makes the area inside of your plenum 1" longer.</strong></b></li><li><b><strong>All exchangers are 3 1/2" thick.</strong></b></li><li><b><strong>Aluminum fins are installed at 12 fines per inch.</strong></b></li><li><b><strong>All exchangers are triple pass design.</strong></b></li><li><b><strong>Tubing is 1/4" copper.</strong></b></li><li><b><strong>All our exchangers include the flat front face mounting for easier installation and increased plenum strength.</strong></b></li><li><b><strong>Our exchangers have 1" copper outlets and can be installed with either sweat fittings or push fit type fittings like sharkbite's.</strong></b></li><li><b><strong>Exchangers from us come with a lifetime warranty, including shipping. </strong></b></li><li><b><strong>Exchangers will work with chilled water also.</strong></b></li><li><b><strong>We stock many sizes, always order the largest size that will fit into your plenum.</strong></b></li></ul><p></p><p style="font-weight: 400;">Installation brackets for installing water to air heat exchangers inside of furnace plenums. This easy to install kit takes all of the work out of installing a coil. Great for the do it yourselfer or the seasoned installer.</p><p style="font-weight: 400;">This kit will work with most coils being sold on other sites that are 3.5" wide. Check before you buy, but that will cover over 90% of the ones being sold. Even most that are listed as 4" are actually 3.5". These will work with every heat exchanger being sold elsewhere and our website store.</p><p style="font-weight: 400;">We provide a<strong><u>lifetime warranty</u></strong>against manufacturer's defects and corrosion.</p><p style="font-weight: 400;"><strong>Dealer inquiries welcomed.</strong></p><h3>These heat exchangers are to be hooked up to a boiler or a chilled water source.</h3><p style="font-weight: 400;">These heat exchangers can also be usedas a stand alone heat source by simply attaching a fan or squirrel cage to one side of the unit. They can be installed in either the hot air side or the cold air return of a furnace. Please note that if installed in the cold air return you will need to install a 3 way zone valve in order for the fan to operate properly.</p><p style="font-weight: 400;"><strong>This heat exchanger is of a new style which does not require bending of your duct work.</strong></p><p style="font-weight: 400;"><strong>This new styleheat exchangercan beeasilyinstalled by just slipping it into theplenum and<u>attaching with self threading screws</u>. Youwill notneed any special tools to install.</strong></p>